CALL US: 0203 8118 306

What Causes Intermittent Lift Faults?

Intermittent lift faults happen when a problem appears only under certain conditions rather than causing a permanent breakdown. Possible causes include inconsistent door locking, deteriorating electrical connections, temperature-sensitive components, unstable power supplies or unreliable sensor signals. The lift may stop working briefly then seem normal again when the operating conditions change.

A lift that starts working again has not necessarily repaired itself. Its controller may have cleared a temporary condition while the underlying defect remains. Establishing the cause requires a competent lift engineer to inspect the installation, review available fault records and test the relevant systems.

For building owners and facilities managers, the most useful approach is to preserve evidence rather than repeatedly reset the lift. Knowing when the fault happens, which floor is involved and what users experience can make an intermittent problem much easier to investigate.

What makes a lift fault intermittent?

A permanent fault is usually present whenever the affected function is tested. An intermittent fault depends on a changing condition. A connection might become unreliable as equipment warms up, a door might fail to prove closed only at one landing or a component might struggle after repeated journeys.

Some intermittent stoppages are protective responses. The control system may prevent movement because it cannot confirm that a required condition has been met. That does not automatically mean a major component has failed, but it does mean the interruption needs proper investigation.

The passenger’s description and the engineering fault are also not always the same thing. Reports such as “the lift ignored my call” or “it stopped for a few minutes” describe symptoms. The engineer must establish whether those symptoms relate to door operation, control inputs, the drive system or another part of the installation.

Common causes of lift faults that come and go

Door locks, alignment and inconsistent closure

A lift normally needs confirmation that the relevant doors are closed and locked before it can travel. If that confirmation is inconsistent, the lift may refuse to start even though the doors appear closed to someone standing outside.

Possible causes include wear in door equipment, alignment changes, damaged contacts or an obstruction affecting closure. A problem limited to one floor may point towards landing-specific equipment. A problem occurring across several floors could involve equipment on the lift car or a shared control function. Neither pattern proves the cause without inspection.

Door behaviour can also change with building conditions. Draughts, pressure differences or debris in an accessible entrance area may affect how a door closes. Repeatedly forcing the door or attempting to adjust equipment is unsafe and can make diagnosis more difficult. Record the affected floor and let the lift engineer investigate.

Electrical connections and components affected by wear

Electrical faults are not always a simple case of a component working or failing completely. A deteriorating connection, worn relay contact or damaged section of wiring may produce an unreliable signal only when equipment moves, vibrates or changes temperature.

Travelling cables and other moving electrical equipment can be relevant where the symptom changes with car position. However, a fault at a particular floor could also have several unrelated explanations. The engineer needs to distinguish a genuine position-dependent electrical problem from a door issue or an incorrect input.

Inspection may involve checking connections, assessing component condition and carrying out suitable electrical tests. This work belongs with competent professionals using appropriate isolation procedures. Building staff should not open control cabinets or attempt to tighten connections.

Temperature, ventilation and operating demand

Some faults appear after a busy period or during warmer weather. Depending on the lift design, drive equipment, motors, control electronics or hydraulic systems may behave differently as operating temperatures rise. Protective functions may then interrupt operation until conditions change.

A lift that runs normally early in the day but becomes unreliable later deserves investigation beyond a simple restart. Engineers may need to assess ventilation, equipment condition, recorded temperatures and the relationship between faults and usage.

The building environment matters too. Changes to ventilation arrangements, nearby refurbishment or storage around equipment spaces may alter conditions. These observations help an engineer form a diagnosis, but they do not justify bypassing protective devices or changing equipment settings without proper assessment.

Power disturbances, sensors and control signals

A brief supply disturbance can affect lift operation without causing an obvious power cut throughout the building. Voltage irregularities or interruptions may trigger protective responses or disrupt control equipment. If several building systems show problems at the same time, that information is worth sharing with the lift contractor.

Position sensors, door detection equipment and other control inputs can also become inconsistent through contamination, deterioration or alignment problems. The controller may receive a missing or contradictory signal only during a particular movement or operating sequence.

On some installations, communication faults between electronic devices can cause sporadic interruptions. Software behaviour or the interaction between replacement components may also require investigation. A displayed code identifies a recorded condition, not necessarily the component that caused it. Engineers should interpret it alongside the installation’s history and test results.

Why does the lift work when the engineer arrives?

An intermittent fault may disappear because the lift has cooled down, demand has reduced or the affected door has completed another operating cycle. A brief electrical disturbance may also have ended before attendance. The absence of a current symptom does not make the original report invalid.

This is why a single successful journey cannot always demonstrate that a recurring fault has been resolved. The engineer may need to recreate relevant conditions safely, examine historical records or arrange further monitoring. Any testing must remain within safe operating procedures.

Timing also matters. If several people restart the lift before an engineer attends, useful information may be lost or the operating state may change. Depending on the controller, some historical events may remain available while other evidence may not. Follow the contractor’s instructions rather than assuming that a reset is harmless or necessary.

How engineers diagnose intermittent lift faults

Effective fault finding starts with a clear account of the symptom. The engineer compares reported behaviour with available controller events, maintenance records and the condition of relevant equipment. The aim is to identify a supported cause rather than replace parts on speculation.

A structured investigation may include:

  • Reviewing fault codes and event sequences where the controller records them.
  • Checking whether separate reports describe the same symptom or different problems.
  • Inspecting relevant doors, connections, sensors and mechanical equipment.
  • Testing operation under appropriate conditions linked to the reported fault.
  • Assessing power quality or environmental conditions where evidence suggests a connection.
  • Using suitable monitoring equipment if the fault cannot be reproduced during attendance.

The order of recorded events can be especially useful. One initial interruption may produce several later warnings, so the last code displayed is not always the starting point. Older controllers may provide limited information, making accurate observations and methodical testing particularly important.

Where a cause remains unconfirmed, the service report should make that distinction clear. “Operating on arrival” describes the condition found during attendance. It should not be treated as proof that no defect exists or that every reported symptom has been explained.

What building teams should record before attendance

A simple shared fault log helps turn scattered complaints into a useful pattern. Ask reception, security and facilities staff to record observations consistently. Separate what somebody directly saw from what they believe caused it.

  • Date and time: Include when the interruption began and when normal operation appeared to return.
  • Location: Identify the lift, affected floor and whether the car was stationary or travelling.
  • Observed behaviour: Note whether doors reopened, calls went unanswered or a display changed.
  • Usage conditions: Record whether the building was busy or whether the issue followed repeated journeys.
  • Other events: Mention power disturbances, unusually hot conditions or nearby building work.
  • Actions taken: Record any authorised intervention and who carried it out.

A photograph of a publicly visible display can help if it can be taken safely without delaying assistance. Do not open panels, enter restricted areas or ask users to recreate a fault. Avoid recording identifiable passengers unnecessarily.

Provide the log to the engineer before or during attendance. A pattern across several reports may be more informative than a general description that the lift is “sometimes unreliable”.

When should an intermittent fault stop the lift being used?

The decision depends on the symptoms and a competent assessment, not simply on whether the lift has started moving again. Unexpected movement, inaccurate stopping at a landing, signs of door security problems, smoke or a burning smell require urgent attention. Do not return a lift to use merely because a warning has disappeared.

Follow the building’s lift incident procedure and contact the lift contractor for advice. Where there is an apparent safety concern, prevent further use through the authorised procedure. Do not improvise isolation methods or place anyone in the lift to test whether the problem returns.

If someone is trapped, use the installed alarm or communication system and arrange competent assistance. Building staff should not force doors or attempt a rescue unless specifically trained and authorised under an appropriate procedure. Call the emergency services where there is immediate danger or a medical emergency.

Choosing between targeted repair, maintenance changes and modernisation

A confirmed intermittent defect may be resolved through a targeted repair or adjustment. Depending on the findings, that could involve restoring reliable door operation, replacing a deteriorated component or correcting an electrical connection. The repair should address the diagnosed cause rather than just clear its warning.

After work, the engineer should test the relevant functions and consider whether the original triggering conditions have been adequately assessed. Where a fault appears only after extended use, a short test may not provide the full picture. Agreed follow-up observations can help confirm whether the symptom returns.

Maintenance changes may be appropriate if repeated issues relate to operating demand, environmental conditions or progressive wear. That could mean adjusting inspection priorities or reviewing the planned maintenance arrangement against the lift’s actual use. Maintenance cannot guarantee that every intermittent fault will be prevented.

Modernisation becomes worth considering where ageing controls, limited diagnostic capability, unavailable parts or several deteriorating systems make reliable repair increasingly difficult. It should follow an assessment of condition and maintainability. One unexplained stoppage alone is not a sound basis for recommending wholesale replacement.

A practical next step for recurring intermittent faults

If a lift repeatedly stops then returns to normal, ask for an investigation focused on the pattern of failure. Share the fault log, request an explanation of what has been confirmed and agree what further evidence is needed if the cause remains uncertain. Clarify whether the lift can remain in service and what should trigger another call.

Excel Lifts brings more than 35 years of lift-industry experience to diagnosis, repair, maintenance and modernisation support. Qualified lift engineers support passenger lifts, goods lifts and platform lifts across a wider service area extending through Southern England to Birmingham. Planned maintenance contracts and 24/7 support for urgent lift faults are available.

The aim is not merely to make the lift run again during attendance. It is to establish why the interruption happened, address supported findings and leave the building team with clear instructions for any recurrence.

Frequently Asked Questions

Can an intermittent lift fault still be investigated without a fault code?

Yes. A fault code can provide useful evidence, but it is not essential for an investigation. Some older lift controllers store little historical information while other faults may not generate a clear diagnostic message. Engineers can compare user reports with equipment condition, service history and appropriate test results. A record of the affected floor, time of day and exact behaviour becomes especially valuable when electronic records are limited. Further monitoring may be needed if the symptom cannot be reproduced safely during the initial visit.

Does remote lift monitoring detect every intermittent fault?

No. Remote monitoring can help identify patterns and record events between visits, but its usefulness depends on the equipment installed and the signals available. It may show that a lift stopped or repeatedly reported a particular condition without identifying the underlying mechanical or electrical cause. Some installations provide much richer diagnostic information than others. Monitoring should support professional inspection rather than replace it. Before adding a system, ask what it records, how alerts are reviewed and how the information will support investigation of your lift’s particular symptoms.

Can refurbishment work elsewhere in a building trigger intermittent lift faults?

It can sometimes contribute, although a connection should not be assumed merely because the timing overlaps. Refurbishment may introduce dust, affect ventilation, alter building pressure conditions or involve electrical work that warrants investigation. Increased deliveries may also change how frequently the lift operates. Tell the lift contractor what work is taking place and when symptoms started. The lift engineer may need to coordinate with the building’s electrical or refurbishment contractor. Building teams should not change lift settings or interfere with protective equipment to accommodate the works.

What should a service report say if an intermittent lift fault was not reproduced?

A useful report should distinguish the reported symptom from what the engineer observed. It should describe relevant checks, available fault records and any findings without presenting an unconfirmed theory as a diagnosis. Where further investigation is needed, ask for the proposed next steps and the information building staff should collect. The report should also make clear any restrictions or instructions about continued use. Recording that the lift was operating on arrival is helpful context, but it does not by itself establish why an earlier interruption occurred.

Lift faults that disappear still need a clear investigation. Contact Excel Lifts to discuss recurring symptoms, professional fault diagnosis and suitable repair or maintenance support for your building.

Are You In Need Of Elevator Repair?

Speak to us today for more information on the range of lifts we repair and install.